How To Install Storm Window Clips

Download Article

Hurricane clips are a fantastic manner of securing potentially hazardous parts of your house in stormy atmospheric condition. These clips work by further strengthening the bail between the roof and the walls of your house and then the roof does not accident away in a hurricane. They are relatively inexpensive and if you lot want to install them by yourself, then they only require a little scrap of care and attention.

ane
Examine your roof for diagonal beams. You lot need to go into the attic of your roof using a ladder and audit the connections betwixt the diagonal beams and horizontal beams. Doing this ways you tin get to the hardware store and exist sure that you are ownership the correct corporeality of clips. Y'all demand a clip for every diagonal beam that attaches to a horizontal beam.^[1]
- Hurricane clips are metal straps that connect the roof truss to the pinnacle of a wall. That way, the roof system won't blow off during a hurricane.^[2]
- Always take caution when using a step-ladder and brand certain you accept someone in that location to hold the ladder still.
2
Buy the H-1 hurricane clips from your local hardware store. Once you've measured how many clips you need, you are set to go out and buy them. Buy a couple extra simply in instance you demand more y'all measured.^[3]
- At that place should exist instructions that come up with the clips and so hang onto these for future reference if you go stuck.
Advertisement
iii
Locate where the pieces of forest meet. Y'all are strengthening the roof by securing two pieces of wood. Ane piece runs parallel to the ground and the other runs diagonally upwardly to come across another piece of wood in the eye.
- The diagonal piece meets the flat piece at the base of operations and this is where the clip goes.
- You may be installing these clips before the diagonal beams have been fitted. If this is the case, simply mark with a pencil where you anticipate the diagonal beams going.^[4]
4
Position the clip so the gap in information technology is pointing forward into the house. The clips have a infinite where the wooden beam can sit in it. This infinite needs to be pointing forward into the house for the clip to work effectively.
- If you lot are having problem figuring out how to position the clip, it attaches to the exterior of the horizontal beam and there will be a 'U' shaped gap where the beam sits in.
- The gap in the clip sits but above the foundation beam and then the diagonal axle tin sit comfortably in it.^[5]
5
Hammer in the clip to the parallel beam using 2.v inches (6.4 cm) nails. Once you've spaced out where you lot are going to attach the clips, they are ready to be fastened. This process starts with nailing them into the parallel beam.
- These nails go through the base of operations plate of the clip.
- In that location are blast holes in the clip and then you don't need to worry about hammering them through the metallic of the clip.
- If you don't have ii.v inches (6.4 cm) nails that's ok, but aim to utilise nails that are as shut to this length as possible. If the nails are also short then the force will be reduced.^[6]

1
Position the diagonal beam and so it is sitting in the open 'U' infinite. This is simply necessary if the diagonal axle going towards the apex of the roof has not been installed yet. If information technology has been installed and so you must fit the clip to the beams rather than the other style around.
- Exercise your all-time to accept the prune completely flat and then that the diagonal axle can come straight through the open up space without needing to exist rotated at all.^[7]
2
Hammer in 2 nails through the clip into the diagonal wood. The nails should be two.v in (6.4 cm), the same as before. This process forms the 2d part of attaching the clips. Employ a minimum of ii nails hither going into the beams. These nails do not go through the base of operations plate of the clip they go through the small extension plate the diagonal beam actually sits in.
- There are holes in the clip where you can hammer the nails through and so you aren't going straight through the steel.
- Feel free to use more than nails if you feel that you demand more to make sure the clip is held secure.
- Brand sure to hammer in the nails all the fashion to ensure the clip is held in there as securely as possible.^[viii]
iii
Repeat this procedure at each meeting of a horizontal and diagonal beam. Your roof or wall will probably have several places where these hurricane clips need to be installed. How many clips you install is completely up to yous. However, for maximum security, install a prune at each indicate a diagonal beam meets a horizontal one.
- If yous practice not install the clips at each opportunity, these spots volition evidence to exist much weaker in a tempest and are at hazard of being blown off.^[9]
- For even more protection, use double ties at each juncture.^[10]
four
Finish off by doing a final bank check over all the clips you lot've installed. When you've gotten to the end and y'all've installed all the clips, it's important to go back and exercise a last check. Doing this allows you to make sure you didn't miss any nails, cheque that the clips are continued in the right places, and ensure everything is secure.
- If you have missed nails on whatsoever clips, simply get back and hammer in the nails where necessary to ensure maximum security.^[11]

Advertizing

Inquire a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertizing

When hammering, ever start with some gentle taps while you agree the base of the blast. Then, once the nail is partially hammered in, accept your hand away and hammer a bit harder at the nail until it is all the way in.